Small quick-connect safety harness 3M Dbi-Sala Delta

Small quick connect safety harness 3M Dbi-Sala Delta. Front and rear attachment points, adjustable on shoulders and legs. It has quick-connect buckles, and tangle-free back pad.

Supply: 5 to 10 working days

DBI-SALA® Delta Harness

CHARACTERISTICS

• Sling Protectors

  Avoid having to carry the sling by hand when it is not being used.
• Covered & i-Safe Labels

  A Velcro® cover protects the harness tags and incorporates DBI-SALA's i-Safe ID tag. It gives you an efficient way to record and store information about inspections.
• No-tangle design (anti tangle)

  As the name implies, the patented triangular design of the DBI-SALA® Delta creates a structure that allows the harness to adapt to the wearer when put on.
• Tangle-free Surefit design

  Surefit ensures the correct position of the harness in the event of a fall while providing additional comfort in everyday use.
• Webbing with Repel technology

  Water repellent to reduce the attraction of mold and dust, making it up to 5 times more resistant to abrasion.
• Revolver Vertical Torso Adjustment System

  Quick and easy adjustments that remove loose ends and secure them in place to prevent slippage.
• Dorsal D-ring that stays elevated

  With its patented spring-loaded design that stands up automatically, it ensures fast, easy and secure connections to the fall protection system.
  Built-in impact indicators

  Drop indicators made up of tear-off stitches allow you to inspect the harness at a glance, evidencing damage from a dynamic load.

TECHNICAL DATA

Improved webbing: Abrasion resistant and water-repellent to reduce mold and mildew generation.

Sling hook housings: Avoid having to carry the sling in your hand when not in use.

Comfort pads: On the lower side of the shoulder, hip and leg straps. ® TM Harness 3M DBI-SALA

Quick Connect Buckles: Lightweight aluminum alloy buckles for quick and easy connections. (There are also models with a thru-buckle.)

Vertical Dorsal D-ring: The vertical Dorsal D-ring ensures quick, easy and secure connections to your fall arrest system. Rigid belt: Allows you to carry 27 kg of tools without breaking. Protected Tags: Harness tags protected with latching and fastening closure.

INSTRUCTIONS FOR USE - FALL ARREST HARNESS ADJUSTMENT

Before you begin. Empty your pockets, as during work or, more importantly, in the event of a fall, the items you carry in the pockets can get caught between the harness straps and the user's body causing injury. Always refer to the instructions for use supplied with the specific harness regarding proper installation and adjustment.

Step 1. Begin. Attach the harness by the D-ring, which is often attached via a D-pad and make sure the straps are not twisted.

Step 2. Shoulder straps. Slide the harness over your arms and place it over your shoulders. Make sure that no straps are tangled and that they hang freely.

Step 3. Leg straps. Place it between your legs and hold the leg strap on your left side. Pull the strap up between your legs and connect it with the buckle on the left side. Connect the webbing to the right leg using the same procedure.

Step 4. Chest straps. Attach the chest webbing buckle to the corresponding opposite side buckle.

Step 5. Waist strap (if equipped). Attach the waist strap buckle to the corresponding opposite side buckle.

Step six. Adjust the harness so it's tight. Adjust the shoulder straps until they are tight with the adjusters. The left and right sides of the shoulder straps should fit to the same length and the breast strap should be centered at the bottom of the chest, about 15 cm below the shoulder. The D pectoral ring of the vest type harness moves up or down adjusting the shoulder and leg straps. Center the D-ring between the shoulder blades. Note: In the applicable models the D-ring can be raised or lowered on the harness strap as necessary to achieve a correct fit. Rearrange the leg straps so they're tight. They shall be at least 8 cm from the strap beyond the buckle on the leg straps. Adjust the belt for the waist (if fitted).

It's ready! A properly fitted and fitted full-body harness will effectively distribute impact forces throughout the body and provide adequate restraint during suspension and rescue after a fall.

REGULATORY

EN 361:2003 - Personal protective equipment against falls from a height. Machinery for making pulp of fibrous cellulosic material

EN 365:2005 - Personal protective equipment against falls from height. General requirements for instructions for use, maintenance, periodic review, repair, marking and packaging.

RECOMMENDATIONS FOR THE CONTENT OF EPI

Do not use this safety equipment unless trained by a competent person (this training may be repeated as often as necessary). Please contact CAPITAL SAFETY for information about the classes or if you have any questions about the use of this equipment. (See full instructions for use).

ABOUT 3M

3M Fall Protection, part of the Personal Protective Products division of 3M, has earned a reputation as experts in safe work at height with our market-leading innovations and high-performance rescue and fall protection solutions. The ultimate protection against falls. What. For more than 75 years, workers at heights around the world have relied on DBI-SALA® products to get their jobs done and home safely. Today, 3M Fall Protection continues that proud tradition by offering high-quality DBI-SALA® fall protection solutions, enabling workers to do their jobs better in a safe and comfortable way.