DBI-SALA ExoFit NEX Large Belt Wind Power Climbing and Positioning Harness 3M

For the purposes of this Regulation, the following definitions shall apply: 3M. What. The wind energy safety harness is comfortable, durable and includes a practical positioning belt at work.

For tower climbing, stay comfortable and protected when using the positioning belt with hip padding Positioning belt at work that allows both hands to be free when used with positioning slings Safety housing with easy opening for hooks Revolver adjustment provides quick and easy vertical adjustment on the torso

Confirm in advance with Sekureco.eu date of supply approx.

CHARACTERISTICS

• This safety harness includes a practical and comfortable work positioning belt that repels water to keep it dry while avoiding the accumulation of mold and dirt.
• These abrasion-resistant belts are durable and can withstand the most demanding everyday conditions.
• Impact indicators make it easier to check for damage to the harness and help ensure its safe use.
• For added comfort, the harness has a built-in radio cover, replaceable lumbar protectors and a protective hip pad that prevents wear when climbing and descending the tower.
• The housing for the sling hook is easy to open to avoid the risk of tripping.
• Because they are lightweight, the Dual-lock quick-connect buckles can be used with one hand and the belt locks keep the settings to ensure quick, slip-free connections.
• Covered identification tags help protect important information during the life of the harness.

BENEFITS

• For tower climbing, stay comfortable and protected by wearing the hip padded positioning belt.
• Positioning belt at work that allows both hands to be free when used with positioning slings.
• Security housing with easy opening for hooks.
• The Revolver Adjuster provides quick and easy vertical adjustment on the torso.
• Dual-lock quick-connect buckles that allow quick, easy and secure connection.
• D-ring in upright position.
• Front and side D-rings made of lightweight aluminium.
• Water-repellent and abrasion-resistant lint that stays dry and strong.
• Integrated anti-trauma suspension straps.
• Integrated radio case.
• Impact indicators make it easier to check for damage to the harness and help ensure its safe use.
• Identification tags are covered.

APPLICATIONS

Suitable for safe operation in the wind energy sector.

TECHNICAL DATA

Improved lines: Abrasion resistant and water repellent to reduce mold and dirt generation.

Sling hooksThe following: Avoid having to carry the sling in the hand when not in use.

Comfort pillowsThe following: On the underside of shoulder, hip and leg straps. TM® Harness 3M DBI-ROOM

Other, of circular cross-section Lightweight aluminium alloy buckles for quick and easy connections. (There are also models with passing buckle).

Vertical back ring in D: The vertical D-ring ensures quick, easy and secure connections to your fall arrest system.

Other, of circular cross-section It can carry 27 kg of unbroken tools. Protected labels: Harness labels protected by fastening.

INSTRUCTIONS FOR USE - ADJUSTMENT OF THE FALL GUARD

Before we start. Empty your pockets, as during work or, more importantly, in the event of a fall, items you carry in your pockets can get caught between the harness straps and the wearer's body, causing injury. Always consult the instructions for use supplied with the specific harness for correct installation and fitting.

Step one. What. Let's get started. Hold the harness by the D-ring, which is often held through a D-pad, and make sure the straps are not twisted.

Step two. You run for the shoulders. Slide the harness over your arms and place it over your shoulders. Make sure no straps are entangled and that they hang freely.

Step three. What. You run for your legs. Place it between your legs and hold the leg strap on your left side. Lift the strap between the legs and connect it to the buckle on the left side. Connect the strap for the right leg using the same procedure.

Step four. What. Chest marks. Attach the breast strap buckle to the corresponding opposite side buckle.

Step five. What. A belt (if you have one). Attach the belt buckle to the corresponding opposite side buckle.

Step six. What. Adjust the harness so it's tight. Adjust the shoulder straps until they are tight with the adjusters. The left and right sides of the shoulder straps should fit to the same length and the breast strap should be centered at the bottom of the chest, about 15 cm below the shoulder. The D pectoral ring of the vest type harness moves up or down adjusting the shoulder and leg straps. Center the D-ring between the shoulder blades. Note: In the applicable models the D-ring can be raised or lowered on the harness strap as necessary to achieve a correct fit. Rearrange the leg straps so they're tight. They shall be at least 8 cm from the strap beyond the buckle on the leg straps. Adjust the belt for the waist (if fitted).

It's ready! A properly fitted and fitted full-body harness will effectively distribute impact forces throughout the body and provide adequate restraint during suspension and rescue after a fall.

REGULATORY

EN 358: 2001 - Personal protective equipment for restraint in working position and preventing falls from height.

EN 361:2003 - Personal protective equipment against falls from a height. Machinery for making pulp of fibrous cellulosic material

EN 1497: 2008 - Personal protective equipment against falls. Lifesaving gear

EN 365:2005 - Personal protective equipment against falls from height. General requirements for instructions for use, maintenance, periodic review, repair, marking and packaging.

RECOMMENDATIONS FOR ALL EPI

Do not use this safety equipment unless trained by a competent person (this training may be repeated as often as necessary). Please contact CAPITAL SAFETY for information about the classes or if you have any questions about the use of this equipment. (See full instructions for use)

ABOUT 3M

3M Fall Protection, part of the Personal Protective Products division of 3M, has earned a reputation as experts in safe work at height with our market-leading innovations and high-performance rescue and fall protection solutions. The ultimate protection against falls. What. For more than 75 years, workers at heights around the world have relied on DBI-SALA® products to get their jobs done and home safely. Today, 3M Fall Protection continues that proud tradition by offering high-quality DBI-SALA® fall protection solutions, enabling workers to do their jobs better in a safe and comfortable way.