Safety harness with Delta rear mounting point 3M DBI-ROOM

Safety harness with Delta rear mounting point 3M IT 'S DBI-SALA . From the best-selling harness range in the world, the new DBI-SALA Delta full-body harness offers industry-first features such as better fit and ergonomic feel, lighter buckles and high-strength straps. Size: S, M, L

Confirm in advance with Sekureco.eu date of supply approx.

CHARACTERISTICS

Racing with Repel technology
Water-repellent to reduce the attraction of mold and dirt, it also has up to 5 times greater abrasion resistance.

Lanyard Keepers
Avoid the need to wear handcuffs when not in use.

Other, of circular cross-section
Simple and quick adjustments that remove loose cables and lock in place, preventing slippage.

Surefit design without tangles
Surefit ensures a correct fit of the harness in the event of a fall, while providing additional comfort for daily use.

Ring on standing back
The patented spring design automatically lifts, ensuring quick, easy and secure connections to your fall arrest system.

No-tangle design
By defining the name DBI-SALA Delta, the patented triangular design creates a frame that allows the harness to fit in place when put on.

Incorporated impact indicators
The ripped stitch indicators allow you to inspect the harness at a glance, to detect previous damaging impact loads.

Covered labels and i-Safe
A Velcro cover protects the harness tags and contains the DBI-SALA i-Safe identification tag. The i-Safe label gives you an efficient way to record and store information at inspections.

BENEFITS

The use of a patented No-Tangle triangular pattern creates a frame that allows the harness to be easily put into place when put on.

The new DBI-SALA Delta harness features liquid-resistant Repel straps and Revolver Torso adjustors, which allow for quick adjustment and eradicate loose strap ends.

Equipped with i-Safe

TECHNICAL DATA

• Weight (kg): 1.40
• Characteristics mooring devices, upright torso adjustment revolver, rear pad without tangles.
• Size: small, unique, extra large.
• Accreditation: BS AT 361.
• The straps: repel the water-repellent belts.
• Setting: adjustable shoulders, chest and legs.
• Other: The standard.
• Capacity: other
• Locations of the D-ring: rear attachment point.

Improved lines: Abrasion resistant and water repellent to reduce mold and dirt generation.

Sling hooksThe following: Avoid having to carry the sling in the hand when not in use.

Comfort pillowsThe following: On the underside of shoulder, hip and leg straps. TM® Harness 3M DBI-ROOM

Other, of circular cross-section Lightweight aluminium alloy buckles for quick and easy connections. (There are also models with passing buckle).

Vertical back ring in D: The vertical D-ring ensures quick, easy and secure connections to your fall arrest system. Rigid belt: Allows to carry 27 kg of unbroken tools. Protected labels: Harness labels protected by coupling and fastening.

INSTRUCTIONS FOR USE - ADJUSTMENT OF THE FALL GUARD

Before we start. Empty your pockets, as during work or, more importantly, in the event of a fall, items you carry in your pockets can get caught between the harness straps and the wearer's body, causing injury. Always consult the instructions for use supplied with the specific harness for correct installation and fitting.

Step one. Let's get started. Hold the harness by the D-ring, which is often held through a D-pad, and make sure the straps are not twisted.

Step two. You run for the shoulders. Slide the harness over your arms and place it over your shoulders. Make sure no straps are entangled and that they hang freely.

Step three. You run for your legs. Place it between your legs and hold the leg strap on your left side. Lift the strap between the legs and connect it to the buckle on the left side. Connect the strap for the right leg using the same procedure.

Step four. Chest marks. Attach the breast strap buckle to the corresponding opposite side buckle.

Step five. A belt (if you have one). Attach the belt buckle to the corresponding opposite side buckle.

Step six. Adjust the harness so it's tight. Adjust the shoulder straps until they are tight with the adjusters. The left and right sides of the shoulder straps should fit to the same length and the breast strap should be centered at the bottom of the chest, about 15 cm below the shoulder. The D pectoral ring of the vest type harness moves up or down adjusting the shoulder and leg straps. Center the D-ring between the shoulder blades. Note: In the applicable models the D-ring can be raised or lowered on the harness strap as necessary to achieve a correct fit. Rearrange the leg straps so they're tight. They shall be at least 8 cm from the strap beyond the buckle on the leg straps. Adjust the belt for the waist (if fitted).

It's ready! A properly fitted and fitted full-body harness will effectively distribute impact forces throughout the body and provide adequate restraint during suspension and rescue after a fall.

REGULATORY

EN 361:2003 - Personal protective equipment against falls from a height. Machinery for making pulp of fibrous cellulosic material

EN 365:2005 - Personal protective equipment against falls from height. General requirements for instructions for use, maintenance, periodic review, repair, marking and packaging.

RECOMMENDATIONS FOR THE SET OF EPI

Do not use this safety equipment unless trained by a competent person (this training may be repeated as often as necessary). Please contact CAPITAL SAFETY for information about the classes or if you have any questions about the use of this equipment. (See full instructions for use).

ABOUT 3M

3M Fall Protection, part of the Personal Protective Products division of 3M, has earned a reputation as experts in safe work at height with our market-leading innovations and high-performance rescue and fall protection solutions. The ultimate protection against falls. What. For more than 75 years, workers at heights around the world have relied on DBI-SALA® products to get their jobs done and home safely. Today, 3M Fall Protection continues that proud tradition by offering high-quality DBI-SALA® fall protection solutions, enabling workers to do their jobs better in a safe and comfortable way.