Harness for welder with 5 set points, with strain of Kevlarcon modacilli 3M

Harness for welder with 5 set points, with strain of Kevlarcon modacilli 3M. Modacrylic Kevlarcon Cinch. It has steel crossing beakes, rear ring in great d. Tag bag. Regulators for the torso. Fall indicators. Rings in D Detention of Falls: 1 dorsal, 1 sternal.

• Designed specifically for welders who work in height exposed to heat and flames
• Dorsal ring in large D that facilitates the connection
• Pectoral cinch located so that it facilitates connection to slings and other systems
• Five adjustment points that allow better adapting the harness offering greater comfort and safety

Supply: From 5 to 10 working days

Features

• Big rear ring

  Being easier to connect and offer greater security, it can be used for the rescue
• Chest strap

  Optimal location for connection to slings and systems
• 5 set points

  It adapts perfectly to the body to enjoy greater comfort and safety
• Pull adjustment

  Easier to adjust.
• Cinch management

  The spare strap is stored on the hip strap.
• Contrast branch and chest strap

  Reduce the assembly time.
• Fall indicator

  Clear indication that the harness must be removed.
• Identification tags covered

  Protects labels during harness life.
• 2-point harness

  Selection of connection points.

Technical data

Improved belts:Resistant to abrasion and water repellent to reduce the generation of mold and dirt.

Accommodation for the slinga hook:Avoid having to take the sling in your hand when it is not in use.

Comfort pads: On the lower side of the shoulder straps, hips and legs. TM® harness 3M DBI-SALA

Quick connection buckles: Light buckles with aluminum alloy for quick and simple connections. (There are also models with passing buckle.).

Vertical dorsal ring in D:The vertical dorsal ring in d guarantees fast, easy and safe connections to your fall arrest system. Rigid belt: allows transporting 27 kgde tools without breaking. Protected labels: Harness labels protected by coupling and clamping.

USE INSTRUCTIONS - AJUST OF ANICAL ARÉS

Before we begin. Empty your pockets, as, during work or, what is even more important, in the case of a fall, the objects that you carry in your pockets can be trapped between the harness's belts and the user's body causing injuries. Always consult the instructions of use supplied with the specific harness regarding the correct installation and adjustment.

Step 1.Start. Hold the harness by the Dorsal Ring in D, which is often attached through a D-inmate and make sure that the straps are not twisted.

Step 2.Shoulders straps. Slide the harness above the arms and place it over the shoulders. Make sure no strap is tangled and that they hang freely.

Step 3.Belts for the legs. Place it between your legs and hold your leg pill on your left side. Climb the belt between the legs and connect it with the buckle on the left side. Connect the strap of the right leg using the same procedure.

Step 4.Pectoral cinches. Set the buckle of the pectoral pill to the corresponding opposite side buckle.

Step 5.Belt for waist (if you have). Attach the belt buckle for the waist to the corresponding opposite side buckle.

Step 6.Adjust the harness so that it is tight. Adjust the shoulder straps until they are tightened with the adjusters. The left and right sides of the shoulder straps must be adjusted at the same length and the pectoral pill should be centered on the lower part of the chest, about 15 cm below the shoulder. The pectoral ring in the vest type harness moves up or down adjusting the shoulder straps and legs. Center the dorsal ring in d between the shoulder blades. Note: In the applicable models the DRESAL ring in d can be upgraded or lowered on the harness cinch as necessary to achieve a correct fit. Re-adjust the straps for the legs to be tightened. They should be at least 8 cm from the strap beyond the buckle on the legs of the legs. Adjust the belt for the waist (if equipped).

It's ready!A whole body harness properly placed and adjusted will effectively distribute impact forces all over the body and provide you with adequate support during suspension and rescue after a fall.

REGULATIONS

EN 361: 2003 - Individual protection equipment against height falls. Fallroom harness

In 365: 2005 - Individual protection equipment against height falls. General requirements for instructions for use, maintenance, periodic review, repair, marking and packaging.

Recommendations for the EPI Conujnto

Do not use this safety equipment unless you have received the training of a competent person (this training may be repeated as often as necessary). Contact Capital Safety for information about classes or if you have questions about using this equipment. Training should be done without exposing the user to a danger of fall and must be repeated periodically. (See the Complete Guide in the instructions for use)

UPON 3M

3M Fall Protection, part of the Division of Personal Protection Products of 3M, a reputation has been gained as experts in safe work in height with our market innovations and high-performance anti-performance rescue and protection solutionsDefinitive protection against falls. For more than 75 years, workers at the height around the world have entrusted DBI-Sala® products to do their work well and get home safely. Today, 3M Fall Protection continues with that proud tradition, offering high quality DBI-Sala® anti-Sala® protection solutions, which allow workers to better work safely and comfortably.