FFP2 particulate mask with valve 9322+Gen3-SP (5 pcs) 3M Aura

FFP2 particulate mask with valve 9322+Gen3-SP (5 units)3M Aura. The 9322+Gen3 is based on the features and advantages of its predecessors to provide greater comfort.

The new Cool Flow Comfort valve opens more easily and stays open longer than the original Cool Flow valve, allowing more hot air to escape to reduce heat buildup and increase comfort.

Confirm in advance with Sekureco.eu approx. supply date.

CHARACTERISTICS

• New braided bands and innovative lashes that offer greater durability and ease of application, repositioning, and removal.
• New valve 3M Cool Flow Comfort. It opens easily, allowing exhaled air to escape for better breathability and comfort.
• Advanced electret filtering medium (AEM) 3M, a high-performance filtering medium designed to facilitate breathing through it.
• With color coding to easily identify the level of protection: blue for FFP2.

BENEFITS

• 3M It has also introduced the Safe Guard product authentication process, which provides the user with greater confidence that the product they are wearing is of original manufacture. 3M.
• The original triple panel foldable design adapts to a wide variety of face shapes and sizes.
• The innovative tabs located on the top and bottom panels of the mask (along with the new 'grip' feature of the valve) allow for easier opening of the mask to simplify its placement and adjustment on the face.
• Braided headbands offer greater durability without compromising user comfort.
• Integrated nasal clip, soft foam for the nose, and a raised and molded top panel help reduce fogging of glasses and provide better compatibility with safety glasses. 3M

COMPONENTS AND MATERIALS

The following materials are used in the production of 3MTM AuraTM Series 9300+Gen3 particle masks:

RESISTANCE TO BREATHING

The breathing resistance of the mask is tested during inhalation and exhalation. The breathing resistance of the masks should not exceed the following limits:

ADJUSTMENT INSTRUCTIONS

Adjustment instructions Refer to the figure

1. Before adjusting the device, make sure to have clean hands. Before each use, all components of the mask should be inspected to ensure they are not damaged. 1. With the back facing up and using the tabs, separate the upper and lower panels.

2. Pull the tabs of the chin and nose panels until the nasal clip bends in such a way that the mask takes on the shape of a cup. Make sure that both panels are fully unfolded.

3. Without releasing the tabs, hold the mask with the open side facing your face and place it over your face.

4a. Mask WITH VALVE: with one hand, hold the sides of the valve to keep the mask in position on the face. 4b. Mask WITHOUT VALVE: hold the mask with one hand with the open side facing the face.

5. With the other hand, take each of the strips and adjust them on your head.

6. Place the upper strap on the crown of your head and the lower strap at the nape of your neck and below your ears. The straps should not be twisted. Adjust the upper and lower panels using the tabs until you feel comfortable. Make sure the panels are unfolded and that the tabs are folded.

7. Shape the nasal clip with both hands to fit the shape of the nose to ensure a precise fit and proper sealing. If you press the nasal clip with one hand only, the effectiveness of the mask may be reduced.

8. Before entering the workplace, you must ensure that the mask is properly sealed to your face.

APPLICATIONS

Protects against low concentrations of dust and common mists in a wide variety of industrial applications and other situations where FFP3 protection is required.

STANDARDS/ REGULATIONS

Products are classified by their filtering efficiency and their maximum total performance against inward leakage (FFP1, FFP2, and FFP3), as well as by their utility and resistance to clogging.

Among the performance tests of this standard are the penetration test through the filter; practical behavior test; flammability test; breathing resistance test; and total inward leakage test.

Reusable products are also subjected to cleaning and storage tests, as well as mandatory obstruction resistance tests (the latter are optional for non-reusable products). You can purchase a complete copy of the standard EN 149:2001+A1:2009 through your country's standardization body.

APPROVALS

These products carry the CE mark as they comply with the requirements of Community Directive 89/686/EEC or European Regulation (EU) 2016/425. To determine the applicable legislation, the Certificate and the Declaration of Conformity should be reviewed on the website. http://www.3M.com/Respiratory/certs These products are approved and are subject to annual audits by BSI, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP, United Kingdom, notified body no. 0086. Manufactured in the United Kingdom, in a facility that has ISO 9001:2008, ISO 14001:2004, and OHSAS 18001:2007 certifications.

VIDEOS