Terminal for 7 cm high rubber speed reducer 3M

Terminal 7000094985 to of a kind used in motor vehicles 3M. What. The gearbox has dimensions of (length 60 cm, width 30 cm).

The terminals allow to supplement the damping of the vehicles, once in use the speed reducers.

CHARACTERISTICS

• High visibility both day and night
• Very easy installation by means of embroidered modules, subsequently fixed to the ground by screws
• Design for excellent water drainage

7cm for speeds below 30km/h. Each element of the gearbox is composed of two parts (male and female) which in turn are assembled with the other elements of the set. It accepts rounded parts at the ends and is fixed with 4 screws per piece.

Length of the part, dimension in the direction of travel of the vehicle.
Piece width, dimension in the width of the driveway.

Modular elements of black rubber incorporating yellow high-retro-reflection non-slip strips.

The contrast between the two materials makes them very visible both day and night. Very easy to install by assembling the machined modules which are then fixed to the floor by screws. Its design allows for perfect drainage.

REGULATORY

Speed reducers 3M are elevated devices, consisting of modular elements of vulcanized natural rubber, with yellow reflective and anti-slip tape inserts 3M Stamark series A651.

In Italy, their use is regulated by the New Italian Traffic Code (Art. 42) and by Decree-Law No 495 of 16.12.92. The three types of gearbox are approved in that country.

In Spain, for the RIGE, these devices are cited in Royal Decree 1428/2003 General Regulation of Traffic, although their full regulatory development is pending. In their field, different Autonomous Communities / Local Authorities have established specific regulations.

They are effective in reducing the speed of vehicles and preserving the safety of pedestrians in urban areas (low speed zones and heavy traffic).

The three types of gear reducers 3M have been approved by the italian government for different facilities.

DIMENSIONS

A speed reducer is a set of elements assembled to form a transverse band on the roadway, to induce drivers to reduce the speed of their vehicles. They are made of rubber and coated with yellow reflective tape to enhance their visibility.

• 7 cm For speeds < 30 km/h each gear element is composed of two parts (male and female) which in turn are assembled with the other elements of the set.

• It supports rounded piece at the ends and is fixed to the floor with 4 screws per piece.

Modules of any type have frames that facilitate composition and distribute effort over the series.

The 5 and 7 cm versions also feature the series' locking terminal modules.

The modules shall have the following dimensions:

-Reducer h 7, for roads with a speed limit < 30 km/h:

The elements of this series are divided into two pieces: male and female overlapping, for reasons of weight and dimensions.

• Central elements (male and female): 50 x 120 cm = 2 x 60 in cm). It is necessary to take 1 male and 1 female.
• Fixation with 6 screws.
• Terminals (male and female): 30 x 120 cm = 2 x 60 in cm). It is necessary to take 1 male and 1 female.
• Fixation with three screws.

Made to order.

FACILITY

The installation of the gear reducers is carried out by means of bolts and expansion studs which allow an optimal ground anchoring during their service life and the possible removal of the elements.

Once the elements have been placed and combined in the final layout, the floor can be drilled with a 10 mm drill bit to a depth of 140 mm. The modules are then removed to allow the bolts to be inserted into the holes; the speed reducers are placed in their correct and final position and the bolts are screwed into the bolts.

It is important that the position of the screw inside the hole is perpendicular to the pavement, to ensure the correct distribution of forces throughout the element. It is also necessary to use steel washbasins of appropriate dimensions.

Important:

• The anchorage system described is the only one that meets our technical specifications and approved by the Italian Ministry of Public Works.
• 3M does not assume responsibility for applications made by other mechanical devices or adhesive techniques.
• The use of any type of adhesive in place of the expansion stick should be avoided as it prevents rainwater from flowing under the gearbox and its possible withdrawal.
• Particular attention will have to be paid to pavements or to the different types of load normally found on our streets; on very rigid surfaces (such as concrete).
• They are especially recommended for urban areas, advising against their installation on high-speed roads as well as on roads subject to heavy traffic.
• No liability can be assumed for installations which do not comply with the conditions described here.

ABOUT 3M

3M is a worldwide scientific enterprise with an unstoppable capacity for innovation. 3M has an integrated team of scientists and researchers who use 46 technology platforms to work with customers and keep innovating. Their innovation has improved the quality of life for hundreds of millions of people around the world.