9332 GEN3 self-filtering folded mask against particles, with Aura high ventilation valve 3M

Self-filtering folded particle mask with Aura valve 3M. Made with sweat-absorbing material. The Mask 3M Aura FFP3 NR D 9332+ provides comfort and design without compromising its effectiveness.

3MTM AuraTM particle masks meet the requirements of the European standard EN 149:2001 A1:2009 for self-filtering particle masks. They offer effective protection of the respiratory tract in those sectors where workers are exposed to solid particles or non-volatile liquid particles.

Respiratory protection is only effective if the appropriate mask is chosen and is fitted and worn correctly at all times the user is exposed to hazards.

Small packaging: 5 units

CHARACTERISTICS

• Nose Clip.
• Made of sweat-absorbing material.
• 3M Advanced design filter material.
• High filtration efficiency combined with low breathing resistance.
• 3M High Ventilation Valve.
• Fastening bands.
• The material of the clamping bands adapts to any head size for an effective adjustment without increasing the voltage.
• Color code indicating the level of protection. Red for FPP3
• Individual packaging.

SPECIFICATIONS

BENEFITS

• Folded
• Patented three-panel design Improves communication and efficiency thanks to its three-panel design.
• It is carried and stored more easily due to its individual and lightweight packaging.
• Its comfort and aesthetics do not compromise its effectiveness.
• Gentle contact to the face.
• Very compatible with glasses, minimizing fogging.
• The innovative VAV valve reduces discomfort, allowing exhaled air to escape from the mask and preventing heat buildup inside.
• Hygienic packaging that protects the mask from any pollution before use.
• Easily carried and stored in the workplace.

COMPONENTS AND MATERIALS

The following materials are used in the production of 3MTM AuraTM Series 9300 Gen3 Particulate Respirators:

ADJUSTMENT INSTRUCTIONS

Adjustment instructions See figure

1. Before adjusting the device, make sure your hands are clean. Before each use, all components of the mask should be inspected for damage. 1. With the back side facing up and using the tabs, separate the top and bottom panels.

2. Pull the tabs on the chin and nose panels until the nose clip bends so that the mask forms a cup shape. Make sure both panels are fully deployed.

3. Without releasing the lashes, hold the mask with the open side facing your face and place it on your face.

4a. MASK WITH VALVE: With one hand, hold the sides of the valve to maintain the position of the mask on the face. 4b. Mask WITHOUT VALVE: Hold the mask in one hand with the open side facing your face.

5. With your other hand, take each of the straps and adjust them to your head.

6. Place the top strap on the crown of your head and the bottom strap on the back of your neck and below your ears. The strips should not be twisted. Adjust the top and bottom panels, using the tabs, until comfortable. Make sure the panels are unfolded and the tabs are folded.

7. Using both hands, mold the nose clip to the shape of your nose to ensure a precise fit and proper seal. Pressing the nose clip with only one hand may reduce the effectiveness of the mask.

8. Before entering the workplace, you must check that the mask is properly sealed to your face.

APPLICATIONS

Protects from low concentrations of dust and mists common in a wide variety of industrial applications and other situations where FFP3 protection is required.

STANDARDS/ REGULATIONS

Products are classified by their filtration efficiency and maximum total inward leakage performance (FFP1, FFP2 and FFP3), as well as by their usefulness and resistance to clogging.

Performance tests of this standard include penetration through the filter; practical behavior test; that of flammability; that of resistance to breathing and that of total leakage towards the interior.

Reusable products also undergo cleaning and storage tests, and mandatory clogging resistance tests (the latter are optional for non-reusable products). You can purchase a complete copy of EN 149:2001 A1:2009 from your national standards body.

APPROVALS

These products carry the CE mark as they comply with the requirements of the community directive 89/686/EEC or the European regulation (EU) 2016/425. To determine the applicable law, you should review the Certificate and Declaration of Conformity on the website http://www.3M.com/Respiratory/certs These products are approved and audited annually by BSI, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP, United Kingdom, Notified Body No 0086. Manufactured in the United Kingdom in a certified plant. ISO 9001:2008, ISO 14001:2004 and OHSAS 18001:2007.

VIDEOS

ABOUT 3M

3M it has such diverse solutions that have the appropriate response to each need. And if this is not the case, they work together with the client to develop that new way of doing things. This different way of thinking is shown in the studies developed to find the most optimal product for each organization.