Speed reducer 60 cm SEKURECO

Speed reducer 60 cm SEKURECO (screws included). Made of recycled black rubber, finished with reflective yellow paint. Installation with screws. The screws included in the price are supplied with the bumps.

Speed reduction bands ideal for forcing vehicles to reduce speed.

The speed reduction bands can be used on streets, parking lots, shopping centers, communities, residential areas...

Fixing the speed reduction bands with anchors. They include male and female joint assemblies.

TECHNICAL DATA

Dimensions: 500 x 900 x 50

Ref: BA20390 (black center)

Screws needed: 5 Ref. BA20000

Dimensions: 250 x 900 × 50

Ref: BA20304 (black male tip)

Ref: BA20305 (black female tip)

Screws needed: 3 Ref. BA20000

LOCATION

The speed reducers covered in this Instruction aim to maintain a speed that should have already been reduced by other measures (for example: signage, roundabouts, etc.), usually placed at the beginning of the crossing or section.
The distance between consecutive speed reducers should be between 50 and 200 m, although it should be ensured that it does not exceed 150 m.

LIMITATIONS

Speed reducers cannot be installed without technical justification in the following cases:

• In sections of the network that are not considered crossings. For these purposes, sections whose circulation, traffic, and uses are similar to those of crossings (for example, near roundabouts in peri-urban areas of roads called "parkway," urban rings, urban penetrations, etc.), and whose speed is less than 50 km/h may be considered crossings.
• In the first 50 meters from the beginning of the crossing, when there is no "entrance gate" (section where a moderate speed is guaranteed).
• In crossings whose length is less than 200 m.
• At points where the V85 exceeds 60 km/h.
• On bridges or tunnels or other singular structures, and in the 25 m before or after.
• In sections of crossings with a slope greater than 5%.
• In sections of crossings where there are more than 2 traffic lanes, unless there is an unbreachable median separating directions.
• In sections of crossings with an IMD greater than 5000 vehicles, or a peak hourly intensity greater than 300 vehicles.
• In sections of crossings with an IMD of heavy vehicles greater than 300 vehicles.
• Near intersections, "speed bump" type speed reducers will not be placed to avoid confusing pedestrians with pedestrian crossings. In this case, only trapezoidal type speed reducers can be used, provided there are pedestrian crossings.

INSTALLATION

• Prefabricated reducers generally consist of modules that are assembled and fixed to the pavement on-site.
• The operations of storage, transport, stockpiling, and installation will be carried out with sufficient care to avoid damage or excessive stresses that could harm the different elements.
• If, after the appropriate checks, modules with defects that could negatively affect their resistance, stability, or behavior are detected, they will be rejected.
• During installation, the assembly of the different modules will be carried out so that the resulting set adapts to the intended shape for the device to be installed.
• The modules and, therefore, the device as a whole, will be fixed to the pavement using screws or chemical adhesives, respecting the tolerances related to the entry edges and ensuring the stability and behavior of the devices against the impact of vehicle wheels passing over them.
• The fixing screws will be perfectly embedded in the reducer without any element or part protruding from the surface of the speed reducer.

NORMS, TESTS, and LEGISLATION:

• UNE 135363
• UNE 135330
• UNE 135350
• UNE 53118
• UNE 53104
• UNE 5328
• UNE EN 13422
• Order FOM/3053/2008

STORAGE, CLEANING, and MAINTENANCE

The working temperature should not exceed 45º C. Higher temperatures may deform the supporting material.
The optimal storage temperature should be between 15º C and 25º C; and with a humidity of 10/50%.
Cleaning methods; avoid applying abrasive products. It is recommended to clean them with water and neutral detergents.

ABOUT SEKURECO

Experts in occupational safety! We are a young and recently established company that emerged in 2016 thanks to the passion of several technicians specialized in prevention and occupational safety. Sekureco offers a range of over 10,000 specialized products in labor protection, available to companies and individuals, from the best brands and at the most competitive prices in the market.